19982005大众新甲壳虫仪表板拆装方法

2024年1月7日发(作者：汽车电瓶多久换一次?)

Instrument panel, removing and installingPage 1 of 14Volkswagen > New Beetle > 1998 - 2005

Body Interior

70 - Interior trim

Instrument panel, removing and installing

WARNING!

Disconnect battery Ground (GND) strap before working on electrical system,

observing all cautions => Repair Manual; Electrical; Repair Group 27,

Battery, disconnecting and reconnecting.

Removing

Note:

Before disconnecting battery Ground (GND) strap obtain security code for radio with anti-theft coding.

Remove driver\'s airbag unit => page 69-50.

Remove steering wheel => page 69-61.

Note:

For vehicles with steering angle sensor -G85- observe:

=> Suspension, Wheels, Steering; Repair Group 48 - Steering; Steering column,

removing and installing; Sequence for vehicles with steering angle sensor -G85-.

For vehicles without steering angle sensor -G85- observe:

=> Suspension, Wheels, Steering; Repair Group 48 - Steering; Steering column,

removing and installing; For vehicles without steering angle sensor -G85-.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 2 of 14

Remove two screws -arrows-.

Remove steering column switch upper trim -1-.

Remove three screws -arrows-.

Release steering wheel height adjustment -2-.

Remove steering column switch lower trim-1-.

Note:

Handle for height adjustment can be removed (two screws) to ease removal of lower

trim.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 3 of 14

Remove Hex socket (Allen key) head bolt -1-.

Disconnect connectors -arrows- from steering column switches.

Remove steering column switch.

Remove screws -1-.

Remove driver\'s side footwell cover -2- from retainers -3-.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 4 of 14Release rear of cover -1- from instrument panel -3- and remove instrument panel to

rear.

Remove bolts/screws -2-.

Slide plenum chamber center cover -1- forward out of its locking device and Remove of

instrument panel -arrow-.

Insert a release tool T10057 into all slots until they engage.

Remove radio from instrument panel using grip rings of release tools and disconnect

electrical connections.

Note:

Radio release tool T10057 must not be pushed to side or canted when being used.

Press locking lugs on sides of radio unit to remove release tools.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 5 of 14

Remove bracket -1- for flower vase -2- from instrument panel.

Disconnect hazard warning light switch connection

Disconnect airbag deactivation warning lamp -K145- connection 05.03

?

Remove screws -3- and remove center air outlet console -4- from instrument panel.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 6 of 14

Pry off cover caps -1- and remove screws -2-.

Remove switch mounting -3- from retainer.

Disconnect electrical connectors from switches.

When existing

Remove auxiliary input jack -1- from bracket -2-.

If necessary, remove bracket -2- from switch mounting -3-.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 7 of 14Remove screws -arrows- (Qty. 6) (screws in center of vehicle are hidden under cover

caps).

Remove glove box -1-.

Disconnect glove box lighting connections.

Release rear of cover -1- from instrument panel and remove.

Remove screws -2- and two screws -3- of fuse holder.

Turn rotary part -1- of lighting switch to position 0.

Press rotary part inward -arrow A- and then to right -arrow B-.

Remove switch out of instrument panel -arrow C- and disconnect electrical connections.

Unclip head light range control switch -2- and disconnect connector.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 8 of 14

Remove 4 screws -1-.

Unclip trim -2- upward and remove from instrument panel.

Remove screws -2-.

Remove impact plate -1- (Convertible).

Remove air duct -1- above center of instrument panel.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 9 of 14

Remove Qty. 3 screws -1-.

Lift left-hand plenum chamber cover -1- in center of instrument panel -arrow A-, this

action unclips panel (front and rear edges are clipped).

Remove cover -1- toward center of instrument panel and out of retainers in A-pillar -arrow B-.

Lift right-hand plenum chamber cover -1- in center of instrument panel -arrow A-, this

action unclips panel (front and rear edges are clipped).

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 10 of 14Remove cover -1- toward center of instrument panel and out of retainers in A-pillar -arrow B-.

Unclip trim -1-.

Remove bolts/screws -2-.

Remove instrument panel insert -3-.

Disconnect multi-pin connections on back of instrument panel insert.

Models without a mobile telephone/cell phone retainer installed

Remove covers-1-.

Remove screws -2- (Tightening torque 8 Nm) and remove handle -3- from instrument

panel.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 11 of 14

Models with mobile telephone/cell phone retainer

Remove screws -3- and -4- from mobile telephone/cell phone retainer

Remove mobile telephone/cell phone retainer -5-.

Remove cover -2-.

Remove screws -1- and remove left retaining plate -6-. Take hand hold -7- off

instrument panel.

Continued for all models

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 12 of 14

Remove 4 screws -1-.

Press heating and ventilation control -2- with attached cables under instrument panel.

Remove screws (2x) and remove Instrument cluster housing -3-.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 13 of 14Remove trim -6-

Remove screws on under side (Qty. 2), upper edge (Qty. 4) and left-hand side (Qty. 1)

of left-hand upper instrument panel -2-. Take upper section of instrument panel -2- off

base unit -5-.

Remove screws on under side (Qty. 4), upper edge (Qty. 4) and right-hand side (Qty. 1)

of right-hand upper instrument panel -4-. Take upper section of instrument panel -4- off

base unit -5-.

Remove screws -5-, M8 bolt -6- and remove frame -7-.

Remove screws -3-, -4- and -8-.

Remove screws securing fuse panel to instrument panel.

Remove instrument panel base unit -1- from cross member -2- and remove of vehicle.

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006

Instrument panel, removing and installingPage 14 of 14Installing

Install in reverse order of removal.

Note:

After reconnecting battery, make sure vehicle equipment (radio, clock, electric windows)

is checked as per Repair Manual and/or Owner\'s manual.

If DTC memory has been erased or Motronic Engine Control Module (ECM) -J220- was

disconnected from battery positive, readiness code must be generated again

=> Repair Manual, Fuel Injection & Ignition, Repair Group 01 On Board Diagnostic;

Readiness code, setting.

After completion of installation on models with ESP, perform basic (default) setting for

Steering Angle Sensor -G85-.

=> Repair Manual, Brake System On Board Diagnostic (OBD), Repair Group 01; On

Board Diagnostic (OBD), performing; Initiating basic setting

If Airbag Malfunction Indicator Lamp (MIL) -K75- signals a malfunction after installation

is complete, then DTC memory must be erased and interrogated again with V.A.G

1551.

=> Repair Manual, Body On Board Diagnostic (OBD), Repair Group 01; Airbag system,

On Board Diagnostic

x-ebahn:///C:/Program%20Files/eBahn/data//VW/A/NB/1/19/2006